備注：     主營產品：LED 鋁框超薄燈箱，led 廣告牌，亞克力燈箱，LED/CCFL磁吸水晶燈箱，LED熒光手寫板，LED魔術鏡面燈箱，     產品特點：         *引進最先進生產技術，嚴格控制產品質量         *使用高質量日本三菱澆筑亞克力板，透光性能好，光線勻稱         *led燈使用壽命超過50，000 小時         *超薄產品，最薄可至10MM         *環保，85%以上的材料可回收   Ma   inly Productions: LED aluminum frame super thin light box, LED advertising sign, Acrylic light box, LED writing board, LED magic mirror light box The  advantages of our products:* Manufactured by the latest technology,*Used high quality LGP (light guide plate) and Acrylic sheet.*Super slim, the thickness of the whole product is 10MM, 20MM, 23MM, and 25MM and so on.*SMD LED light source has a long lifetime.*Eco-recyclable, 85% materials can be recycled.     目錄一：安全說明Safety Instructions …………………………… …………………………… ……………………1 二：燈箱剖析圖Light Box's Profile chart …………………… …………………… …………………… ……….2 三 ：安裝步驟Installation’s steps……………………………………………………………………………… 2.3 四：常見問題的解決方法Common problems and solutions…………………………………………………………………4 五：警告、注意Warning，Attention…………………………………………………………………………….....5 六：產品認證Certifications ………………………………… ………………………………… ………………5  燈箱安裝使用說明書Light box Setup and use instructions 使用產品前請詳細閱讀并注意以下安全防范以確保正確使用本產品Please read the instructions carefully before using the product. 一：安全說明（ Safety Instructions ）為了讓您更放心和有效地使用本公司的產品，請由專業人員安裝本產品 環境 -------- 不要在高溫(40 ℃ 以上）、潮濕（80% 以上）的地方使用。 電源 -------- 接通電源前,請檢查產品所標示電壓（見燈箱背面）是否與該場地電壓相符，切勿超負荷使用。 清潔 -------- 本產品耐磨力為 2h ,清潔時注意勿用微粒清潔產品及腐蝕性清潔產品。 In order to effectively and correctly use of our products, please install the products from the professionals Environment --- Do not use the light box above temperature (over40 ℃ )and humidity (over80%) of the places. Power --- Please check whether the product voltage (back of light box) is the same to the place voltage before switch on. Do not overload. Cleaning— 2h abrasive resistance, Do not use particle cleaning product and corrosiveness product.  三 ：安裝步驟（附圖） --- --- --- --- Installation’s steps (with photos) 1 、確定燈箱安裝的位置，根據實際情況和燈箱品種，確定安裝方法。 2 、 測量尺寸:根據燈箱背面的安裝孔位置或現場實際尺寸來確定安裝燈箱的固定點。 3 、接線:正常燈箱電源線的出口端在背面,(自配有電源線),直接接入電源即可。 4  、固定燈箱：把燈箱的上蓋打開，對正固定點安裝（即用電鉆在燈箱底座電源線位置鉆孔，用水平尺調整成水平狀態 ） ； 5  、 通電亮燈，清潔燈箱表面即可。 6  、定期檢查燈箱，延長燈箱使用壽命 7、 導光板超薄燈箱采用電子鎮流器，易產生感應電，安裝時注意接好地線以示安全。  1 .Conform the location of installation of light boxes, according to the actual situations to determine the installation’ s methods. 2... Measure size: According to the place and the light box size, measures the installation’s size. 3. Connect wire: Normally the exit end of the power line is at the back of the light box, (power line included), connect the power. 4. Fix the light-box Open the front cover of the light box, match the assembling point. Using electronic drill the hole at the back of the power line position, fix the new power line, use the ruler to keep it is straight 5. Switch on and clean the light box surface. 6. Please do the periodical inspections then could prolong light box using life. 7. LGP of light box adapt to electronic ballast, can easy make the electric induction. For your safety, please pay attention to connect the ground  

四：常見問題的解決方法（ Common problems and solutions ） 若使用本產品時出現異常情況，請參照下表情況排除處理。  普通超薄燈箱   鏡面超薄燈箱   If the light box was Abnormality, Please refer to the table exclude processing conditions  五：警告、注意（ Warning! Attention! ）  六：產品認證（ Certifications ）我們的產品電源通過 CE,ROHS等認證，電源適配器擁有各個不同國家的認證，您可以放心安全使用。Our product has pass CE ，ROHS。 Power switching adapter with all kinds of certifications, enjoy your using!